1. Fanuc
  2. Series 30i-MODEL A, Single Direction Positioning

Series 30i-MODEL A, Single Direction Positioning Additional Manual Page 1

Additional Manual
TECHNICAL REPORT NO. TMN 04/020E
Date :Mar .30, 2004
General Manager of
Software Laboratory
FANUC Series 30i-A Newly additional functions
1. Communicate this report to:
Your information only
GE Fanuc-N, GE Fanuc-E
FANUC Robotics
MILACRON
Machine tool builder
Sales agency
End user
2. Summary for Sales Documents
3. Notice
Applied software of FANUC Series 30i-A
G001/22(V) or later
G011/22(V) or later
G021/22(V) or later
4. Attached Document
Drawing No. refer to attached table
Copy :
FLB1 Manager (2 pages from cover)
FLB2 Manager (2 pages from cover)
FLB3 Manager (2 pages from cover)
Original section of issue
Vice
General
Manager
Manager Chief
Person in
Charge
No. FLB1-04/2218
Date Mar. 30, 2004
ADE
Previous page
Next page

Contents Summary of Series 30i-MODEL A, Single Direction Positioning Additional Manual

  • Page 1TECHNICAL REPORT NO. TMN 04/020E Date :Mar .30, 2004 General Manager of Software Laboratory FANUC Series 30i-A Newly additional functions 1. Communicate this report to: Your information only GE Fanuc-N, GE Fanuc-E FANUC Robotics MILACRON Machine tool builder Sales agency End user 2. Summary for Sale
  • Page 2FANUC Series30i –A newly additional functions Drawing number Functions 1 A-79227E External Data Input 2 A-79226E One Touch Macro call 3 A-79196E Temporary absolute coordinate setting 4 A-79354E System alarm 5 A-79349E Touch Panel Control 6 A-79253E Distance coded linear scale interface 7 A-79364E Li
  • Page 3FANUC Series 30i-MODEL A Single Direction Positioning SPECIFICATIONS FANUC Series 30i-MODEL A Title Single Direction Positioning Draw A-79358E No. Ed. Date Design Description Sheet 1/7 Date Jan.06.’04 Desig. Apprv.
  • Page 41.1 SINGLE DIRECTION POSITIONING General For accurate positioning without play of the machine (backlash), final positioning from one direction is available. Overrun Start position Start position End position Temporary stop Fig.1.1 (a) Direction positioning process Format G60 IP_ ; IP_ : For an absol
  • Page 5Explanation An overrun and a positioning direction are set by the parameter (No. 5440). Even when a commanded positioning direction coincides with that set by the parameter, the tool stops once before the end point. G60, which is an one-shot G-code, can be used as a modal G-code in group 01 by setti
  • Page 6• Overview of operation In the case of positioning of non-linear interpolation type (bit 1 (LRP) of parameter No. 1401 = 0) As shown below, single direction positioning is performed independently along each axis. X Overrun distance in the Z-axis direction Overrun distance in the X-axis direction Pro
  • Page 7Parameter #7 #6 #5 #4 #3 #2 #1 #0 5431 PDI G60 [Input type] Parameter input [Data type] Bit #0 G60 Specifies whether the G60 code (single direction positioning) is a one-shot G code (00 group) or modal G code (01 group). 0: One-shot G code (00 group) 1: Modal G code (01 group) #1 PDI In the G60 mode
  • Page 8Limitation • Single direction positioning is not performed along an axis for which no overrun distance is set in parameter No. 5440. • Single direction positioning is not performed along an axis for which travel distance 0 is specified. • The mirror image function is not applied in a parameter-set d
  • Page 9Note NOTE ・ This function is optional. FANUC Series 30i-MODEL A Title Single Direction Positioning Draw A-79358E No. Ed. Date Design Description Sheet 7/7 Date Jan.06.’04 Desig. Apprv.