1. Fanuc
  2. FANUC Series 30i/31i/32i-MODEL A, Connecting to 2 LCD Units, Specification

FANUC Series 30i/31i/32i-MODEL A, Connecting to 2 LCD Units, Specification Additional Manual Page 1

Additional Manual
TECHNICAL REPORT (MANUAL) NO.TMN 05/119E
Date: Dec. 7, 2005
General Manager of
CNC Laboratory
Connection of two LCD units for Stand-alone type FS30i-A/31i-A5/31i-A/32i-A
1. Communicate this report to:
○ Your information
○ GE Fanuc-N, GE Fanuc-E
FANUC Robotics
MILACRON
○ Machine tool builder
Sales agency
End user
2. Summary for Sales Documents
3. Notice
This function needs the following CNC software series/edition
CNC control software
: G002,G101,G121,G012,G022,G201,G111,G131 /16.0 or later
Graphic software
: 60V8 /15 or later
60VA /13 or later
60VD /08 or later
BOOT software
: 60W1 /17 or later
4. Attached Document
Drawing
No.
A-65568EN/01 (1/9-9/9)
A-90365EN/01 (1/5-5/5)
FANUC
ADE
Original section of issue
Vice General
Manager
Department
Manager
Section
Manager
Person in
Charge
Previous page
Next page

Contents Summary of FANUC Series 30i/31i/32i-MODEL A, Connecting to 2 LCD Units, Specification Additional Manual

  • Page 1TECHNICAL REPORT (MANUAL) NO.TMN 05/119E Date: Dec. 7, 2005 General Manager of CNC Laboratory Connection of two LCD units for Stand-alone type FS30i-A/31i-A5/31i-A/32i-A 1. Communicate this report to: ○ Your information ○ GE Fanuc-N, GE Fanuc-E FANUC Robotics MILACRON ○ Machine tool builder Sales ag
  • Page 2FANUC Series 30i/31i/32i -MODEL A Connecting to 2 LCD units Specification FANUC Series 30i/31i/32i -MODEL A Title Connecting to 2 LCD units Draw A-90365EN No. Ed. Date Design Description page 1/5 Date 2005.10.11 Design. N.Hatanaka Apprv.
  • Page 3Table of contents 1.1 OUTLINE 3 1.2 SPECIFICATIONS 4 Signals 5 FANUC Series 30i/31i/32i -MODEL A Title Connecting to 2 LCD units Draw A-90365EN No. Ed. Date Design Description page 2/5 Date 2005.10.11 Design. Apprv.
  • Page 41.1 Outline In stand alone type CNC, a control unit with 2 LCD units are available. The same screen is displayed on 2 LCD units at the same time. The specifications of LCD units are as follows. specifications Note 1st unit A02B-0303-C072 10.4” color LCD (without touch panel) 2nd unit A02B-0303-C073
  • Page 51.2 Specifications In stand alone type CNC, a control unit with 2 LCD units are available. The same screen is displayed on 2 LCD units at the same time. The specifications of LCD units are as follows. 1st LCD unit 2nd LCD unit 1st MDI unit 2nd MDI unit CNC The MDI units can be connected to each LCD
  • Page 6Signals MDI selection signal MDISL [Classification] Input signal [Function] Select the effective side of MDI unit [Operation] Input signal Selected MDI MDISL 0 1st MDI unit 1 2nd MDI unit MDI selection check signal MMDISL [Classification] Output signal [Function] Check the