FANUC Series 16i/18i/21i-MB, FANUC Series 18i-MB5 Retraction for 3-Dimensional Rigid Tapping, Specifications Additional Manual Page 7
Additional Manual
2005/08/29
Edit
7/8
Data Si
g
nature
Descri
p
tion
FS16i/18i/21i-MB, 18i-MB5
Retraction for 3-dimentional rigid tapping
Specifications
A-90190EN
Drawing No.
Title
Page
5 Parameter
#7 #6 #5 #4 #3 #2 #1 #0
5200 DOV
[Data type] Bit
DOV For tool retraction during rigid tapping, the override is
0: Disabled.
1: Enabled.
#7 #6 #5 #4 #3 #2 #1 #0
5202 RG3
[Data type] Bit
RG3 Rigid tapping retraction during 3-dimensional coordinate conversion mode or tilted
working plane command mode is performed using
0: Input signal RTNT <G062#6>.
1: G30 program command.
5381 Override for rigid tapping retraction
[Data type] Byte
[Unit of data] %
[Valid data range] 0 to 200
Sets an override value to be applied to rigid tapping retraction. No override is
applied if 0 is set to this parameter.
5382 Retract value α for rigid tapping retraction
[Data type] 2 word
[Unit of data] Input unit
[Valid data range] 0 to 99999999
Sets an extra retract value for rigid tapping retraction. The tool will be pulled beyond
the R point by α. If rigid tapping retraction has already been completed, the tool is
pulled by α only.
N
ote
When this parameter is set, the CNC power must be turned off before
operation is continued.
N
ote
This parameter is enabled when the parameter DOV (No.5200#4) is
set to “1”.
Contents Summary of FANUC Series 16i/18i/21i-MB, FANUC Series 18i-MB5 Retraction for 3-Dimensional Rigid Tapping, Specifications Additional Manual
- Page 1FANUC Series 16i/18i/21i-MB FANUC Series 18i-MB5 Retraction for 3-dimensional rigid tapping Specifications Contents 1 GENERAL ............................................................................................................................................... 2 2 SPECIFICATION.............
- Page 21 General When the 3-dimensional rigid tapping or the rigid tapping during tilted working plane command is stopped by a result of the CNC power off, an emergency stop or a reset, the tap may cut into the workpiece. The tap can subsequently be drawn out by using a PMC signal or a program command. Thi
- Page 32 Specification The retraction of the 3-dimensional rigid tapping or the rigid tapping during tilted working plane command is executed triggered by Rigid tapping retraction start signal RTNT
- Page 42.2 Retraction for rigid tapping by G30 program command When the parameter RG3 (No.5202#1) is “1”, this method is used. Specification method When rigid tapping has been stopped as a result of an emergency stop or a reset, or when the CNC power has been disconnected during rigid tapping, execute the
- Page 53 Note 1. When the retraction movement is only for the retract value α, which is set in the parameter No.5382, the retraction movement is executed at the program coordinate on the 3-dimensional coordinate conversion mode or tilted working plane command mode. 2. At the retraction for rigid tapping by
- Page 64 Signal Rigid tapping retraction start signal RTNT
- Page 75 Parameter #7 #6 #5 #4 #3 #2 #1 #0 5200 DOV [Data type] Bit DOV For tool retraction during rigid tapping, the override is 0: Disabled. 1: Enabled. #7 #6 #5 #4 #3 #2 #1 #0 5202 RG3 [Data type] Bit RG3 Rigid tapping retraction during 3-dimensional coordinate conversion mode or tilted working plane co
- Page 86 Alarm and message No Message Contents 5384 RETRACT FOR RIGID CANNOT BE At the retraction for rigid tapping by G30 program CMD. command, the program coordinate at the rigid tapping stopped is different from that at the rigid tapping retraction. FS16i/18i/21i-MB, 18i-MB5 Title Retraction for 3-dimen