FANUC Series 16/18 MC 16i/18i MA toollife management b Additional Manual Page 5

Additional Manual

Page of 14

/ 14

ページ

nature Description

1998/09/21

FS16/18-MC , FS16i

18i-M

Tool Life Management B

A-63526E

Title

Drawin

No.

Edit Data

Note 1) If the arbitrary group number is set to the same number at other groups, PS158

alarm is generated.

Note 2) Please set arbitrary group number (1-99999999). If the arbitrary group number is

not set, PS149 alarm is generated.

Note 3) It is not possible to set to the arbitrary group number by exceeding eight digits.

If the arbitrary group number by exceeding eight digits is set, PS003 alarm is

generated.

Note 4) If the decimal point is set in the arbitrary group number, PS007 alarm is generated.

And if the sign is set in the arbitrary group number, PS006 alarm is generated.

Note 5) Please the number of permissible digits of T codes (parameter No.3032) to eight

digits.

（２）The data setting by extended tool life management (data editing screen for the group).

It is possible to edit the arbitrary group number by using the extended tool life management

(data editing screen for the group).

The edit method is done by the same method as other items. That is,

The cursor is matched to the arbitrary group number.

↓

The numerical value is input.

↓

The soft key ［INPUT］ is pushed.

Note 1) The arbitrary group number is possible to edit as other items.

Note 2) If the same number already exists when an arbitrary number is set, a warning is

generated.

Note 3) The value of the group cannot be set by exceeding maximum value (99999999). If

the value is set, a warning is generated.

Contents Summary of FANUC Series 16/18 MC 16i/18i MA toollife management b Additional Manual

Page 1FANUC Series 16/18-MC FANUC Series 16i/18i-MA Tool Life Management B Specifications Software Software Software Laboratory Laboratory ＦＬＢ１ Section ＦＬＢ１ Section Title FS16/18-MC , FS16i/18i-MA Tool Life Management B Drawing No. A-63526E ページ Edit Data Signature Description 0/13 1998/09/21 ＤＳ００００－００１版
Page 2FANUC Series 16/18-MC FANUC Series 16i/18i-MA Tool Life Management B Specifications 1.TOOL LIFE VALUE EXPANSION (999999TIMES/100000MINUTES) ........................................... 2 1.1. GENERAL .....................................................................................................
Page 31. Tool life value expansion (９９９９９９９９９９９９times／１０００００９９９９９９／１０００００minutes）／１０００００） 1.1.General Though the maximum value of the tool life could be set 65535 times or 4300 minutes by the tool life management, the value is possible to expand for 999999 times or 100000 minutes by using the option
Page 42. Arbitrary tool group number setting 2.1.General By using this function (parameter No.6802#5), it is possible to specify the group by using an arbitrary T code instead of the group by using T code of tool life management ignore No. + Group No. 2.2.Setting method （１）The data setting by programming
Page 5Note 1) If the arbitrary group number is set to the same number at other groups, PS158 alarm is generated. Note 2) Please set arbitrary group number (1-99999999). If the arbitrary group number is not set, PS149 alarm is generated. Note 3) It is not possible to set to the arbitrary group number by ex
Page 62.3. Use method The arbitrary group number is specified same as usual tool life management with T code. But tool life management ignore number (parameter No.6810) cannot be used. Example) When tool of the group is used after arbitrary group number 12345 is set to group No. 1 Ｏ０００１；Ｔ１２３４５； → tool se
Page 73. Tool life notice signal 3.1.General When‘Tool life value(LIFE)-life counter value(COUNT)' reaches the value that is the remainder of tool life until selecting a new tool for each groups, signal (TLCHB) is output to PMC. 3.2.Setting method The remainder of tool life until selecting a new tool (rem
Page 8（２）The data setting by extended tool life management (data editing screen for the group). It is possible to edit the remaining tool life by using the extended tool life management (data editing screen for the group). The edit method is done by the same method as other items. That is, The cursor is m
Page 93.3. Use method When the tool counter is added 1 and ‘Tool life value (LIFE)-life counter value (COUNT)' reaches the value (remaining tool life value), signal (TLCHB) is output to PMC. Example) It is assumed that group No. 1 is in the state when life is controlled by the frequency as follows. ＥＤＩＴＬ
Page 103.4.Note Note 1) The parameter of the extended tool life management is necessary. Note 2) The signal is turned on as follows. （1） When value of‘LIFE-COUNT' and value of remaining tool life of each group is the same. → "Equal" type （2） When value of‘LIFE-COUNT' is smaller than value of remaining tool
Page 113.5. Parameter data No. #7 #6 #5 #4 #3 #2 #1 #0 6802 RMT ARL GRP ＧＲＰ Data for the notice signal （TLCHB）is used by ０ : parameter Ｎｏ．６８４４，Ｎｏ．６８４５１： data to be set for each group ＡＲＬ The notice signal (TLCHB) is ０： output each tool １： output last tool in the group Note）This parameter is effective when
Page 124. Display The group number is displayed 8 digits, the count and life data number is displayed 6 digits in the tool life screen and extended tool life screen. 【tool life management display】ＴＯＯＬＬＩＦＥＤＡＴＡ：Ｏ０００１Ｎ０００００ＮＸＴ９９９９９９９９ＵＳＥ０００００００１ＳＬＣＴ０００００００１００１：０００００００１：ＣＬＩＦＥ１０００００ＣＯＵＮＴ１０００００
Page 13【extended tool life management display（notice signal）】ＥＤＩＴＬＩＦＥＤＡＴＡＧＲＰ：９９９９９９９９ＴＹＰＥ：２（１：Ｃ２：Ｍ）ＵＳＥＧＲＯＵＰ：０００００００３ＬＩＦＥ：１０００００ＳＥＬＥＣＴＥＤＧＲＯＵＰ：０００００００２ＣＯＵＮＴ：１０００００ＲＥＳＴＣＯＵＮＴ：１０００００ＮＯ．ＳＴＡＴＥＴ－ＣＯＤＥＨ－ＣＯＤＥＤ－ＣＯＤＥ０１＊０００００００１００２００３０２＃０００００００４００５００６０３＠０００００００７００８００９０４＊００００００１
Page 145. Comparisons between Tool Life Management and Tool Life Management B Tool life management B is upper compatible with tool life management. function tool life tool life note management B management extended tool life management 〇〇６８０１＃６ tool life count override 〇〇６８０１＃２ life count by 1 sec 〇〇