FS 16i/18i-MA, Spindle electronic gear box, A-77833E Additional Manual Page 12

Additional Manual

Page of 19

/ 19

FANUC Series 16i /18i -MA

Spindle electronic gear box

ecifications

EDT. DATE DESIG. DESCRIPTION PAGE /19

A – 77833E

NO.

TITLE

NEWLY

1999.July.28

5) In case that the parameters for axis setting (No.7710,7771,4352) are not

set correctly, P/S alarm (No.010) occurs when G81 specified.

6) When G28/G27/G29G30/G30.1/G53 is specified in the synchronization

mode, P/S alarm (No.184) occurs. G28/G27/G29/G30/G30.1/G53 should

not be specified in the synchronization mode.

7) During HPCC mode with RISC, the high-speed cycle cutting, the high-speed

liner interpolation, the high-speed remote buffer A, the high-speed remote

buffer B of DNC operation, and AI contour control, this function is not available.

8) The slave axis position display is updated by synchronous pulse as follows :

- Machine position display is updated.

- Absolute position display and relative position display are not updated. When

the synchronization is canceled, the pulses of the synchronization are added

to the absolute position display of the slave axis.

9) The rotation direction of the workpiece axis depends on the rotation

direction of the tool axis. That is, when the rotation direction of the tool axis

is positive, the rotation direction of the workpiece axis is also positive; when

the rotation direction of the tool axis is negative, the rotation direction of the

workpiece axis is also negative. However, by specifying a negative value for

L, the rotation direction of the workpiece axis can be made opposite to the

rotation direction of the tool axis.

10) During synchronization, a move command can be programmed for the workpiece

axis. Note, however, that incremental command programming for cutting feed

must be used to specify the workpiece axis move command.

11) The synchronization mode is canceled by servo alarm, spindle alarm, P/S alarm

(No.000), or emergency stop.

12) The synchronization is not maintained in servo off status of the slave axis.

13) When the EGB control is used, the drilling canned cycle cannot be used.

14) The actual feedrate is displayed without the flexible synchronous pulse.

Contents Summary of FS 16i/18i-MA, Spindle electronic gear box, A-77833E Additional Manual

Page 1FANUC Series 16i /18i -MA Spindle electronic gear box Specifications Contents 1 General --------------------------------------------- 2 2 Operation --------------------------------------------- 4 2.1 Format -------------------------------------------- 4 2.2 Parameter setting ------------------------
Page 21. General A gear can be shaped (grind/cut) by the synchronization of the workpiece axis rotation to the tool axis (grinding axis /hob) rotation by using two spindles as a tool axis and a workpiece axis. To synchronize these two axes, the Electronic gear box (EGB) is used. In the Spindle EGB, the sy
Page 3CNC 2nd spindle (Slave) Position feedback Velocity feedback - - + Position + Velocity Built-in Work- Cs + control control motor & piece command Position gain (PI) Detecto (Gear) + + K2/K1 : Synchronous ratio α : Feedforward ratio αs EGB mode K2 K1 Position feedback - - Velocity feedback Position Vel
Page 42. Operations 2.1 Format G81 T_ L_ Q_ P_ ; Starts synchronization. G80 ; Cancels synchronization. T : Number of teeth (Specifiable range : 1 to 1000) L : Number of hob threads (Specifiable range : -200 to 200 with 0 excluded) Q : Module or diametral pitch Specify a module in the case of metric input
Page 52.3 Starting/canceling of synchronization When the rotation of the tool axis (master axis) starts after G81 is specified, the EGB synchronization starts with the synchronous relationship specified in G81 block, and the rotation of the workpiece axis (slave axis) starts. When the EGB synchronization
Page 6Program example Axis configuration X,Y,Z, B(Cs axis: tool axis/master axis), C(Cs axis: workpiece axis/slave axis) O1000 ; N00010 G80 ; N00020 G28 G91 B0 C0 ; Performs reference position return operation of the tool and the workpiece axis. N00030 G81 T20 L1 ; Starts synchronization. N00040 Mxx ; Rot
Page 72.4 Helical gear compensation When a helical gear is to be produced, the compensation of the workpiece axis rotation is needed according to the travel distance on the Z-axis (axial feed axis: parameter No. 7709 setting). Helical gear compensation is performed by adding compensation pulses calculated
Page 8The direction of helical gear compensation is determined by bit 2 (HDR) of parameter No.7700 (1 is usually specified). The compensation direction is shown in figure 2.4. (1) When bit 2 (HDR) of parameter No.7700 is 1. (a) (b) (c) (d) +Z +Z +C +Z +C +Z +C +C -Z -Z -Z -Z C: + C: + C: + C: + Z: + Z: +
Page 92.5 Synchronous ratio The synchronous ratio of the Spindle EGB control is internally represented using a fraction. The fraction is calculated from T and L command in G81 block and the number of position detector pulses per rotation about the tool and the workpiece axis (parameter setting). K2 L B Sy
Page 10Example) When the pulses for one rotation (360000) are specified to the tool axis (master axis) on the following conditions, the pulses for position control are distributed as figure 2.6. Hob threads L : 10 Number of teeth of the work T : 100 Number of pulse per one revolution of position detector o
Page 112.6 Retract function When the retract signal RTRCT(G66#4) is turned to “1” in auto mode (MEM, MDI, etc.) or manual mode (HNDL, JOG etc.), the axis set in bit 0 (RTR) of the parameter No.7730 moves (retracts) by the amount set in the parameter No.7741. Note1) Feedrate in retract is set to the paramet
Page 125) In case that the parameters for axis setting (No.7710,7771,4352) are not set correctly, P/S alarm (No.010) occurs when G81 specified. 6) When G28/G27/G29G30/G30.1/G53 is specified in the synchronization mode, P/S alarm (No.184) occurs. G28/G27/G29/G30/G30.1/G53 should not be specified in the sync
Page 133. Parameters 3.1 Parameters for serial spindle 4036 Feed forward coefficient for serial spindle [Data type] Word [Valid data range] 0 to 10000 Feed forward coefficient for Cs contour control axis is set. Specified value is smaller than or equal to 100 : In units of 1% Specified value is greater tha
Page 144387 Numerator of synchronous ratio [Data type] Word [Valid data range] -32767 to 32767 Numerator of synchronous ratio is set to this parameter automatically when G81 is specified. 4388 Denominator of synchronous ratio [Data type] Word [Valid data range] 1 to 65535 Denominator of synchronous ratio i
Page 153.2 Parameters for synchronous control 7 6 5 4 3 2 1 0 7700 HDR HBR C C C C C C HD C C [Data type] Bit axis HBR The synchronization is : 0 : Canceled by reset. 1 : Not canceled by reset. 1 is usually specified. HDR Setting of the direction for helical gear compensation (1 is usually specified.) 7709
Page 167772 Number of position detector pulses per rotation about tool axis [Data type] 2-Word [Data unit] Detection unit [Valid data range] Set 360000 to this parameter. This parameter specifies the number of pulses per rotation about the tool axis (master axis), for the position detector. 7773 Number of
Page 173.3 Parameters for retract function 7 6 5 4 3 2 1 0 7730 RTRx C C C C C C C C [Data type] Bit axis RTRx The retract function is : 0 : Disabled. 1 : Enabled. 7740 Feedrate during retraction for each axis [Data type] 2 Words axis [Unit of data and valid data range] Increment system Unit of data Valid
Page 184. Signals 7 6 5 4 3 2 1 0 F065 SYNMOD Synchronization mode signal SYNMOD [Classification] Output signal [Function] Confirmation of the EGB synchronization [Operation] The signal becomes “1” when : - The EGB synchronization is active. The signal becomes “0” when : - The EGB synchronization is cancel
Page 195. Alarm and message Number Message Contents 010 IMPROPER G-CODE Parameters for axis setting are not set correctly regarding G81. (No.7710,7771,4352,or Cs axis setting). Confirm the parameter setting. 181 FORMAT ERROR IN G81 G81 block format error BLOCK 1) T(number of teeth) has not been instructed.