FANUC Series 16i/18i/21i-MB/TB Improvement of Program Restart Specifications Additional Manual Page 16

Additional Manual

Page of 22

/ 22

7. Parameter

#7 #6 #5 #4 #3 #2 #1 #0

7300 CCS

[Data type] Bit

CCS When a spindle used for Cs contour control is in spindle mode, or when

reference point of Cs contour control axis is not established, program

restart is

0: Not available.

1: Available.

7310 Movement sequence to program restart position

Setting entry is accepted.

[Data type] Byte axis

[Valid Data range] 1 to no. of controlled axes

This parameter sets the axis sequence when the machine moves to the

restart point by dry run after a program is restarted.

#7 #6 #5 #4 #3 #2 #1 #0

13114 DRM

[Data type] Bit

DRM During program search of program restart, the state of the

diameter/radius is decided by M code which is specified in parameters.

This function is :

0: Not available

1: Available

Caution

Specify M code for Diameter mode in parameter No.3419,

and M code for Radius mode in parameter No.3420.

Edit

16/22

Data Si

nature

Descri

tion

Improvement of Program restart Specifications

A-90024EN

Drawing No.

Page

Modification

Date

Mar/26/05.

Desig.

M. Kobayashi

Apprv.

T. Endo

May/10/05.

FANUC Series 16i/18i/21i-MB/TB

Title

Contents Summary of FANUC Series 16i/18i/21i-MB/TB Improvement of Program Restart Specifications Additional Manual

Page 1FANUC Series 16i/18i/21i -MB/TB Improvement of Program restart Specifications Contents 1. IMPROVEMENT OF PROGRAM RESTART .............................................................................. 2 1.1 GENERAL ......................................................................................
Page 21. Improvement of Program restart 1.1 General This function enables the following functions in the program restart. - M/S/T/B codes, which are found in search of the block to be restarted, can be output into MDI program. And M/S/T/B functions can be executed by MDI program. - In case that the system
Page 38) Change to the MDI mode, and then check the MDI program. If need, modify the MDI program, and then press the cycle start button. (When program restart signal SRN becomes “0” and program restart MDI program output completed signal SQMPR becomes “1”, PMC ladder can select the MDI m
Page 41.2.2 M/S/T/B codes output into MDI program M/S/T/B codes, which are found in search of the block to be restarted, can be automatically output into MDI program by CNC. Caution - Up to 50 M/S/T/B codes or addresses of arguments for macro call can be output. - If there is no M/S/T/B code to be output,
Page 5(Example) Block to be restarted is N100 in a program O100. Setting of M code groups: - M10, M11 : Group 2 - M120, M220, M320 : Group 3 - M51 : Group 0 (No group) O0100; M10 -- Group 2 : M11 -- Group 2 : M120 -- Group 3 M codes to be output : M51 -- Group 0 M10 : M10 -- Group 2 M51 : M220 -- Group 3
Page 61.2.3 Output of M code used to call sub program/custom macro program In M/S/T/B codes output into MDI program, M code used to call sub program and M code used to call custom macro program and arguments can be output into the MDI program. Caution - The MDI program, into which M/S/T/B codes are output
Page 7Caution The result of conversion is expressed by up to 8 digits, decimal point and minus sign. If the result cannot be expressed by 8 digits, P/S alarm 5373 occurs. (Example) The following arguments cannot be converted into 8 digits, and P/S alarm 5373 occurs. - M20 A[12345678.*10.] ; (123456780. ,
Page 82) Move the cursor to the target axis by up and down-arrow keys then input the movement order of the axis. Caution - When the axis movement sequence is changed in the program restart screen, also value of parameter No.7310 changes. - If the input value is “0” or exceeds controlled axis number, warni
Page 92. Program restart for Flexible synchronous control (FS16i/18i-B) 2.1 General Program restart function is enabled at the program with the M code which changes synchronization mode of flexible synchronous control. 2.2 Details 2.2.1 Setting of parameter When parameter FRS (No.13421#0) is set to "1", P
Page 10(3) If a command to the axis which was slave axis is specified after the cancel of synchronization and before specifying the absolute command to the axis which was slave axis, P/S alarm No.5377 occurs. (Example) C : Master axis, A : Slave axis O0002 ; N10 C0 A0 ; N20 M133 ; <------- Synchronization
Page 11(3) When the flexible synchronization mode is on at the program restart block, the distance to go of the slave axis becomes "0". And "*********" is displayed at the destination of the slave axis. (Example) C : Master axis, A : Slave axis (4) In case that a block after turning off synchronization is
Page 122.2.4 Continue of synchronization at emergency stop or servo off In the current specifications, the synchronization is canceled at emergency stop or servo off. When the parameter FCN (No.13421#1) is set to "1", the synchronization is enabled to continue. (This function enables independently of the p
Page 133. Program restart for Cs contour control axis Generally, Cs contour control mode must be on and the reference point of Cs contour control axis must be established before starting program restart operation. However, when Cs-axis coordinate establishment function is used and parameter CCS (No.7300#5)
Page 145. Program restart for Dynamic Diameter/Radius switch function (M series) In case that program restart is performed on the program using Dynamic Diameter/Radius switch function, set parameter DRM (No.13114#6) to 1. And Diameter/Radius mode must be switched by two M codes, which are specified in para
Page 156. Caution in program restart (1) When parameter INT (No.13117#4) is set to 1, interference check for cutter compensation C (M series) or tool nose radius compensation (T series) can be suppressed during program restart. (2) When parameter SQB (No.13117#6) is set to 1, program restart by specifying
Page 167. Parameter #7 #6 #5 #4 #3 #2 #1 #0 7300 CCS [Data type] Bit CCS When a spindle used for Cs contour control is in spindle mode, or when reference point of Cs contour control axis is not established, program restart is 0: Not available. 1: Available. 7310 Movement sequence to program restart positio
Page 173419 M-code of diameter mode [Data type] Byte [Valid Data range] 1 to 255 It is recognized that the first axis is a diameter mode during the program search of program restart when parameter DRM (No.13114#6) is set to "1". Value 0 is invalid. 3420 M-code of radius mode [Data type] Byte [Valid Data ra
Page 18SQB Program restart by specifying a block number is 0: Available 1: Not available SQP Program restart P-Type is 0: Available 1: Not available #7 #6 #5 #4 #3 #2 #1 #0 13421 FRF FCN FRS [Data type] Bit FRS Program restart at the program with the M code which changes synchronization mode of flexible sy
Page 198. Signal Program restart signal SRN [Classification] Input signal [Function] Selects program restart. [Operation] When the program restart signal is set to “1” to search for the sequence number of the block to be restarted, the CRT screen changes to the program restart screen. When the prog
Page 20Program restart MDI program output completed signal SQMPR [Classification] Output signal [Function] Indicates M/S/T/B codes output into MDI program is completed. [Operation] The program restart MDI program output completed signal becomes “1” when: - M/S/T/B codes output into MDI program is c
Page 21Memory protection signal KEY3, KEY1 [Classification] Input signal [Function] Enables MDI program editing. [Operation] In M/S/T/B output into MDI program by program restart, KEY3 or KEY1 signal enables MDI program editing. When parameter KEY (No.3290#7) is set to 0, KEY3 is available.
Page 229. Alarm No. Message Meaning of data 5373 AURGUMENT CONVERSION In MDI program output for ERROR program restart, macro call argument cannot be converted into 8 digits. 5374 FSC MODE MISMATCH IN The current mode of flexible RESTART synchronous control is different from the mode at the program restart