APPENDIX
B. LIST OF SPINDLE PARAMETER
NUMBERS
B–65160E/02
346
1st spindle 2nd spindle
Spindle switching
MAIN side
Spindle switching
SUB side
Spindle switching
MAIN side
Spindle switching
SUB side
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
High
–speed
charac-
teristics
Low
–speed
charac-
teristics
Contents
3000 ² 3320 ² 3140 ² 3540 ² Bit parameter
3001 ² 3321 ² 3141 ² 3541 ² Bit parameter
3002 ² 3322 ² 3142 ² 3542 ² Bit parameter
3003 ² 3323 ² 3143 ² 3543 ² Bit parameter
3004 ² 3324 ² 3144 ² 3544 ² Bit parameter
3005 ² 3325 ² 3145 ² 3545 ² Bit parameter
3006 ² 3326 ² 3146 ² 3546 ² Bit parameter
3007 ² 3327 ² 3147 ² 3547 ² Bit parameter
3008 ² 3328 ² 3148 ² 3548 ² Bit parameter
3009 ² 3329 ² 3149 ² 3549 ² Bit parameter
3010 ² 3330 ² 3150 ² 3550 ² Bit parameter
3011 ² 3331 ² 3151 ² 3551 ² Bit parameter
3012 ² 3332 ² 3152 ² 3552 ² Bit parameter
3013 ² 3333 ² 3153 ² 3553 ² Bit parameter
3014 ² ² ² 3154 ² ² ² Bit parameter
3015 ² ² ² 3155 ² ² ² Bit parameter
3016 ² 3336 ² 3156 ² 3556 ² Bit parameter
3017 ² 3337 ² 3157 ² 3557 ² Bit parameter
3018 ² 3338 ² 3158 ² 3558 ² Bit parameter
3019 ² 3339 ² 3159 ² 3559 ² Bit parameter
3020 ² 3340 ² 3160 ² 3560 ² Maximum motor speed
3021 ² 3161 ² Maximum speed in Cs contour control
mode
3022 ² 3341 ² 3162 ² 3561 ² Speed arrival detection level
3023 ² 3342 ² 3163 ² 3562 ² Speed detection level
3024 ² 3343 ² 3164 ² 3563 ² Speed zero detection level
3025 ² 3344 ² 3165 ² 3564 ² Limited torque
3026 ² 3345 ² 3166 ² 3565 ² Load detection level 1
3027 ² ² ² 3167 ² ² ² Load detection level 2
3028 ² 3346 ² 3168 ² 3566 ² Limited output pattern
3029 ² 3347 ² 3169 ² 3567 ² Output limit
3030 ² ² ² 3170 ² ² ² Soft start/stop time
3031 ² 3348 ² 3171 ² 3568 ² Stop position in orientation by position
coder
3032 ² ² 3172 ² ² Acceleration/deceleration time constant
during spindle synchronization
B.2
FOR FANUC
Series 15